How to MAKE BOOTABLE PENDRIVE USING CMD [Command Prompt]

Bootable USB is a disk that is used to boot up a computer system for the installation of an Operating System. A USB can be made bootable using a command-line only for computer that have Windows 7 or above version operating system.

Early versions of Windows such as before Windows 7 cannot be used for making a USB bootable. Linux Distributions cannot be used to create a bootable USB device without using third-party tools.how to create bootable pendrive using cmd

Amlodipine: (Minor) In vivo studies suggest eslicarbazepine is an inducer of CYP3A4. Desoximetasone has been shown to be teratogenic and embryotoxic in mice, rats, and rabbits when given by subcutaneous or dermal routes of administration in doses 3 to 30 times the human dose of desoximetasone cream USP, 0. If you become pregnant while using darbepoetin alfa injection, call your doctor viagra apotheke in Hamburg. Like other topical corticosteroids, mometasone furoate has anti-inflammatory, antipruritic, and vasoconstrictive properties.

All patients were adults, had compensated liver disease, detectable hepatitis C virus, liver biopsy diagnosis of chronic hepatitis C, and were previously untreated with interferon. Jardiance and Invokana are both in the same class of medications: sodium-glucose co-transporter (SGLT2) inhibitors. In rats, PCC, aPCC, and rFVIIa significantly decreased bleeding times www.farmacias-semreceita.com. Losartan may not decrease the risk of stroke in African Americans who have these conditions.

You can create a bootable USB flash drive to use to install Windows Server Essentials. Firstly you need to prepare the USB flash drive by using DiskPart, which is a command-line function.

How to create a bootable USB flash drive

Command-prompt in Windows is easily accessible in all the versions of Windows. To create a bootable USB flash drive using a command prompt is quite an easier task. You can follow the steps given below in order to make your USB flash drive bootable.

Step 1: First of all, you need to insert a USB flash drive into a running computer.

Inserting USB device

Step 2: And then open a Command Prompt window as an administrator.

To open Command Prompt window as an administrator, Search for “cmd” in Start menu, and “right-click” on the command prompt, now click on Run as Administrator.

Bootable USB Using CMD

Step 3: Now type “diskpart” command.

Diskpart commant prompt

Step 4: In the new command line window that opens, to determine the USB flash drive number or drive letter, at the command prompt, type “list disk”, and then click the ENTER key. The list disk command displays all the disks on the computer screen. Note the drive number or drive letter of the USB flash drive.

create bootable pendrive list disk

Step 5: At the command prompt, type select “disk <X>”, where X is the drive number or drive letter of the USB flash drive, and then click ENTER key.

Note: –

Select the disk that pen drive to be make bootable. Commonly, pen drive is marked as Disk 1, but it might vary system to system. Ensure that you did not select any other available disk as it will get formatted.

create bootable pendrive select disk x

Step 6: Type “clean” and the click the ENTER key. “clean” command deletes all data from the USB flash drive.

create bootable pendrive clean

Step 7: To create a new primary partition on the USB flash drive, you need to type “create partition primary”, and then click ENTER key.

create bootable pendrive create partition primary

Step 8: To select the partition that you just created, type “select partition 1”, and then click ENTER key from the keyboard.

create bootable pendrive select partition x

Step 9: To format the partition, type” format fs=ntfs quick”, and then click on the ENTER key.

create bootable pendrive format

Important

If your server platform supports Unified Extensible Firmware Interface (UEFI), you need to format the USB flash drive as FAT32 rather than as NTFS. To format the partition as FAT32, type format fs=fat32 quick, and then click the ENTER key.

Step 10: Type “active”, and then click on the ENTER key.

create bootable pendrive active

Step 11: Type “exit”, and then click on the ENTER key to exit DISKPART.

create bootable pendrive exit

Now close the command prompt window and follow the next step.

Step 12: Now copy all the data from the OS installation disk to save it to the root of the USB flash drive.

Now, this Pen drive can be used to install the beloved Operating System on any computer.